Handicare · fault codes

Handicare stairlift error codes and problems

Handicare stairlift error codes appear on a one-character display on the straight 1100 and 1000 models: 0 usually means the key or the stop button, a dash means an armrest or the seat, 2 means it is not charging, 4 or 6 an obstruction, 7 a flat battery, and letters such as d, o and Y mean call Handicare. The curved Freecurve has no display; it uses a lamp on the armrest and beeps. Everything here comes from Handicare's own manuals and its owners' site, Handicare TechTool.

Last checked: , against the makers' own documents Not affiliated with any manufacturer

The codes on the 1100 and the 1000

The two straight models share most of their codes, but not all, and a few mean slightly different things. Both manuals head their code pages the same way: if the action shown does not help, call Handicare, and write the code down before you ring (Handicare 1000 manualp.25).

Handicare 1100 and 1000 display codes side by side, in short
DisplayHandicare 1100Handicare 1000
blank Sleeping Off, or asleep
- Armrest up or seat turned Armrest folded up
0 Key off or stop pressed Key, stop button or seat
1 Needs charging Needs charging
2 Not charging Off charge
3 Top end limit End limit
4 Top safety edge Safety edge
5 Bottom end limit End limit
6 Bottom safety edge Safety edge
7 Battery too low to ride Low battery
8 Going up Going up
9 Going down Going down
d Main power relay Main power relay
L Overload or motor fault Overloaded
o Control board memory Control board memory
Y Hardware fault Main board fault

The 1000 also has C, E, F, g, H, n, r, U, . | | ., .8.; the 1100 also shows Ir, rF, FP, SL and noSL and a short self-test. Full meanings, checks and pages are on the Handicare 1100 and Handicare 1000 pages.

The 0 and the dash: the commonest stops

On the 1100, 0 means either the key switch is off or the emergency stop button has been pressed, and the dash means an armrest is folded up or the seat is swivelled. On the 1000, the seat moves to the 0 group and the dash is the armrest alone. The fixes are the same: turn the key on, press a lit stop button once to release it, fold both armrests fully down, and turn the seat back with the handle under it until it clicks (Handicare 1100 manualpp.19-20). TechTool's 1100 page adds that the display is under a grey cover behind the seat, and on the 1000 it is under the seat behind the footrest.

Beeping, and the 2

A Handicare that beeps after you park it is not charging, and each model beeps for a different length of time. The 1100 manual says the lift beeps for 40 seconds and shows 2 when its batteries are not recharging, possibly because the plug is out of the socket. The 1000 beeps for 15 seconds and shows 2 when it is not sitting correctly on a charge point or is unplugged (Handicare 1000 manualp.8). The Freecurve beeps for three minutes with its armrest lamp flashing. Handicare's checks are the plug, on every model, and on the 1000 and Freecurve the charge point at the top or bottom of the rail. Its manuals also say never to take the lift's plug out of the wall socket. Stair lift beeping compares other makes.

Won't move, or one way only

A lift that will travel one way but not the other, showing 4 or 6 (the manuals print it as "4/6"), has met an obstruction between the lift and the stairs: drive it the opposite way and remove what is there (Handicare 1100 manualp.22). A 7 means the battery is too low to ride; the 1100 manual says to wait about 30 minutes before the next trip. An L is a load problem: TechTool says the lift is overloaded and to take weight off it. TechTool also lists a step for 4 and 6 that involves pushing on the footplate and its underpan; that touches the safety edges, so this guide leaves it to an engineer. See keeps stopping.

The Freecurve: a lamp instead of codes

The curved Freecurve tells you what is wrong with a small lamp on the armrest. Dark when you push the joystick means the key is off; lit but not moving means an armrest is up; flashing means the seat is turned or there is an obstruction, depending on whether it will move one way; and a lit stop button means press it once (Freecurve manualpp.20-23). The full list, with the remote control's lamp, is on the Handicare Freecurve page.

Resets, model by model

Handicare's three models handle resets differently. For an 1100 installed before May 2024, TechTool's reset is the key: turn it off, wait 30 seconds, turn it back on. For later 1100s its reset involves removing a cover to reach a switch, which this guide does not set out. The 1000 manual says a display showing anything other than its listed codes needs a reset: drive the lift off the charge contacts, then switch the main switch on the unit off for 10 seconds and back on (Handicare 1000 manualp.27). The Freecurve manual says a reset is only for an emergency and only by a certified engineer. How to reset a stair lift compares the makers.

Where Handicare's own sources differ

Handicare's 1000 manual says to turn the key a quarter turn clockwise; TechTool's 1000 page says anti-clockwise. Its earlier 1100 manual reads a red light on the remote as flat remote batteries; TechTool treats a red light as a working remote. Both versions are given on the model pages, so you can match what you see.

What Handicare publishes, and where

Handicare's owners' site, TechTool, is run by Handicare Stairlifts B.V. and has a fault-finder for each model and the user manuals. The 1100 manual it links now is the 2023 edition, which has a five-point malfunction checklist but no code table; the code table is in the earlier full edition, still on the same site. Handicare's UK website could not be read for this guide (it refused the request), so its troubleshooter page is not used here. Every manual is listed in the manual finder.

If a code is not in your model's list, or the check does not clear it, Handicare's instruction is to call it with the code written down; if the lift is under a warranty or a service plan, use that. Stairlift Support is independent and not affiliated with Handicare; the repair quote form on this page reaches SEO Dons Ltd, which replies by email.

Where this comes from

Each meaning, check and number above is taken from the documents listed here, opened on the maker's own website. Page numbers in the text are the numbers printed in each manual. How the makers' documents are checked.

Get a stair lift repair quote

For when the maker's manual says it is a job for an engineer. Give the make, the model and what the lift shows or does. Replies come by email, so this is not the way to get help for someone stuck on a lift now.

After you press send

  1. SEO Dons Ltd, which publishes Stairlift Support, receives what you send.
  2. Someone reads the make, the model and the fault, and replies by email.
  3. There is no obligation: asking does not commit you to any repair.
Add the model and the exact code, light or beep (optional)

Stairlift Support is published by SEO Dons Ltd, which has no engineers and no link to any stair lift maker. Answers come by email. Someone stuck on a stair lift who is hurt or in danger needs 999, not this form. How details are used: privacy notice.

Get a stair lift repair quote
Get a stair lift repair quote