What is different about a 420
Three details matter when you work through the checks. The master power switch is on the rear of the chair, and Stannah says the 420 will not work with it off (420 Starla guidep.9). On the Starla chair the power key goes in the side of the chair and has to be pushed fully in; when it is in and the on/off switch is on, the light on the switch comes on (p.10). And the 420 has a seat sensor: it travels on the arm control only with someone sitting down, although the remote calling controls still move it empty (p.7).
The checks, as Stannah gives them
Beeping while it is parked
What the maker says it means: Stannah's 420 page says the beep usually means the batteries are not charging properly. The lift can still run on its batteries.
- The wall switch is in the on position.
- There is no power cut in the house.
- With a hinged rail, hold the up arrow on a remote calling control so the hinged rail goes fully up.
If that does not work: Still beeping: turning the master power switch off silences it. Then call your local Stannah service branch.
Will not move, power light off
What the maker says it means: The 420 has no power to its controls: the master power switch or the power key is off.
- Switch the master power switch on: on the 420 it sits on the rear of the chair and is normally left on.
- Put the power key in and turn it to on.
If that does not work: If the light will not come on, call your Stannah supplier.
Will not move, power light on
What the maker says it means: The chair has power but is being held: the seat position, an obstruction or the hinged rail.
- The chair is turned back to its travelling position with the swivel levers fully down.
- No obstruction on the safety edges; if there is one, move the lift the other way and remove it.
- A hinged rail, if fitted, is fully down.
If that does not work: If none of these frees it, use the restart below, then call your Stannah supplier.
Still stuck after the checks
What the maker says it means: The 420 guide gives the same downward restart as the later guides.
- Key off, then on again.
- Hold the control downward; the lift should start after a few seconds.
- Repeat both if it stops again before the bottom.
If that does not work: Call your Stannah supplier once you are down. If the restart fails, ask another person in the home to call your supplier.
Remote calling controls not working
What the maker says it means: Stannah's 420 page points first to the handset batteries, which last about a year with average use.
- Press an arrow button and watch the light around the buttons: on all the time means the battery is low, no light means it has no power.
- Change the batteries as the user guide shows (page 19 of the Starla guide).
If that does not work: If the remote still does nothing, contact your local Stannah branch.
Beeping and the hinged rail
A 420 that beeps while parked is, by Stannah's account, usually a lift whose batteries are not charging properly (Stannah 420 support pageweb page). The wall switch and a power cut are the first two checks. A hinged rail adds a third: if the rail is down, the lift sits at the bottom of the stairs blocking the way and off its charge point. Holding the up arrow on a remote calling control raises the rail fully and moves the lift to where it charges (420 Starla guidep.13). While the hinged rail moves, a light flashes and the lift beeps on purpose, to warn people nearby.
If none of that stops it, Stannah allows the beeper to be silenced by turning the master power switch off, and then asks you to call your local Stannah service branch. With the master switch off the lift will not charge, so that call should not wait. Stannah beeping compares the three models.
Will not move
Read the power light first. With it off, Stannah's two checks are the master power switch on the rear of the chair and the power key. With it on, the chair has power and is being held: check it is swivelled back with the swivel levers fully down, that nothing is pressing the safety edges, and that a hinged rail, if fitted, is fully down (Stannah 420 support pageweb page). If something is against an edge, the guide says the lift can be moved the opposite way so you can take it out. Keeps stopping covers safety edges on every make.
If it stops with you on it
Hurt, or unable to get off safely: call 999
Stannah's restart is for someone who is safe and able to use the controls.
The 420 guide's restart is the same pattern as Stannah's later guides: key off, key back on, then hold the control downwards and wait a few seconds for the lift to start; repeat if it stops again before the bottom (420 Starla guidep.22). Once down, call your Stannah supplier. If the restart does not work, ask another person in the home to call, and carry a mobile phone whenever you use the lift alone. The guide's last resort is to swivel the chair towards the top of the stairs, undo the belt and get off up the stairs. Its hand-winding instructions involve holding a safety edge and are for engineers here. See stuck on the stairs.
Remote calling controls
Each 420 remote calling control takes three AA batteries, which Stannah says last about a year with average use (420 Starla guidep.19). Press an arrow to check them: rotating lights are fine, lights on constantly mean change them soon, and no light means they are flat. The controls work only when the lift is switched on. Stannah's 420 page sends you to the user guide for changing them.
Stannah 420 battery replacement
The batteries in the lift itself are not an owner's job. Stannah's battery page tells owners never to replace a stairlift battery themselves, as it risks voiding their cover, and says its engineers carry approved batteries (Stannah batteries pageweb page). It lists the signs that the batteries are wearing out: the lift runs slower than usual, stops after a short distance and then carries on, or will not charge at its usual point. Stannah publishes no battery price. Battery replacement sets out what each maker says.
Is there a Stannah 420 repair manual?
Not one that Stannah publishes. Its public documents for the 420 are the three user guides ("Looking after your stairlift"), and repair and service manuals for stair lifts are written for trained engineers. This guide works only from user guides and the maker's own support pages, and stops where they say to call an engineer.
The 420 guides
Stannah's 420 product-support page links three guides: Starla (Issue 1, March 2011), Saxon (Issue 7, April 2011) and Sofia or Solus (Issue 8, April 2011). Their help pages match on the points above. The manual finder links each, and the Stannah page has the 600 and 260.
Where this comes from
Each meaning, check and number above is taken from the documents listed here, opened on the maker's own website. Page numbers in the text are the numbers printed in each manual. How the makers' documents are checked.