Charging a 1000
The 1000 charges at charge points at the top and bottom of the rail, and there may be more along it (Handicare 1000 manualp.8). If the chair is not sitting correctly on one, it beeps for 15 seconds and the display shows 2. The manual's fix for that code is to move the lift onto a charge point or put the plug back in its socket (p.20). Handicare says the lift does not work if the batteries are flat, so a lift left off charge will eventually stop where it is.
A second charging code, r, means a power supply fault while charging. Its two pictures in the manual show the on/off switch on the unit and the plug in the wall, and TechTool's 1000 page says to check the power cord is plugged in and all power switches are on (Handicare TechTool, 1000web page). A U, a power fault while the battery is on float charge, has a telephone on its tile: call Handicare.
Handicare 1000 stairlift battery replacement
The 1000 manual has no battery-changing instructions for owners, and its guarantee terms exclude batteries. Its battery codes point the same way: 1 and 7 say charge it, and if the action shown does not help, call Handicare. If a well-charged 1000 keeps falling back to 7, tell Handicare or your engineer the code and how long a charge lasts. Battery replacement compares what each maker says, and how long batteries last gives each maker's figure where one is published.
Every 1000 display code
The manual's code pages carry the same two lines as the 1100's: if the action shown does not help, call Handicare, and write the code down when you call (Handicare 1000 manualpp.25-27). TechTool's 1000 page puts the display under the chair seat, behind the footrest, which may need lowering before you can read it.
| Shows | What the maker says it means | What the maker lets you check | When it needs an engineer | Where it says so |
|---|---|---|---|---|
| blank | No display: the lift is switched off, or asleep if it is already on. | Switch it on at the on/off button on the front of the lift (the footrest may have to be lowered to reach it). If it was on, use the toggle or a remote to wake it. | Both Handicare code pages say: if the action shown does not help, call Handicare, and write the code down first. | Handicare 1000 manualpp.21, 25 |
| - | Charging, but it will not drive, probably because an armrest is folded up. | Fold both armrests fully down. | Both Handicare code pages say: if the action shown does not help, call Handicare, and write the code down first. | Handicare 1000 manualpp.19, 25 |
| 0 | Three causes share it on the 1000: the key switch is off, the stop button has been pressed, or the seat is swivelled and unlocked. | Turn the key to on (the manual says a quarter turn clockwise; TechTool says anti-clockwise, so turn it to the ON mark); press a lit stop button once; turn the seat back with the handle under it until it clicks. | Both Handicare code pages say: if the action shown does not help, call Handicare, and write the code down first. | Handicare 1000 manualpp.18-19, 25 |
| 1 | The batteries need charging. | Park the lift on a charge point. | Both Handicare code pages say: if the action shown does not help, call Handicare, and write the code down first. | Handicare 1000 manualp.25 |
| 2 | Not charging: the lift is not sitting properly on a charge point, or its plug is out. It beeps for 15 seconds when this happens. | Move the lift onto a charge point, or put the plug back in the socket. | Both Handicare code pages say: if the action shown does not help, call Handicare, and write the code down first. | Handicare 1000 manualpp.8, 20, 25 |
| 3 | A track limit has been triggered: the top one on a lift fitted on the left of the stairs, the bottom one on a right-hand lift. | No owner check given. | No owner action is printed; if it will not move away from the end, call Handicare. | Handicare 1000 manualp.25 |
| 4 | A safety edge has been pressed (the top one on a left-hand lift, the bottom one on a right-hand lift); it will now go one way only. | Drive it the opposite way and remove the obstacle. | Both Handicare code pages say: if the action shown does not help, call Handicare, and write the code down first. | Handicare 1000 manualpp.21, 25 |
| 5 | The other track limit: bottom on a left-hand lift, top on a right-hand one. | No owner check given. | No owner action is printed; call Handicare if the lift stays stuck at the end. | Handicare 1000 manualp.25 |
| 6 | The other safety edge (bottom on a left-hand lift, top on a right-hand one) has been pressed. | Reverse the lift and take out what is in the way. | Both Handicare code pages say: if the action shown does not help, call Handicare, and write the code down first. | Handicare 1000 manualpp.21, 25 |
| 7 | The battery voltage is low; the tile's picture shows the lift parked on its charge point. | Park it on a charge point. | Both Handicare code pages say: if the action shown does not help, call Handicare, and write the code down first. | Handicare 1000 manualp.26 |
| 8 | The joystick is being used to go up. | No owner check given. | Nothing to fix: the lift is doing what it should. | Handicare 1000 manualp.26 |
| 9 | The joystick is being used to go down. | No owner check given. | Nothing to fix: the lift is doing what it should. | Handicare 1000 manualp.26 |
| C | An infrared address fault. | No owner check given. | Telephone on the tile: call Handicare. | Handicare 1000 manualp.26 |
| d | The main power relay is not opening. | No owner check given. | Call Handicare. | Handicare 1000 manualp.26 |
| E | The main power is not closing. | No owner check given. | Call Handicare. | Handicare 1000 manualp.26 |
| F | The brake's semiconductor has failed. | No owner check given. | Call Handicare. | Handicare 1000 manualp.26 |
| g | The brake is not connected. | No owner check given. | Call Handicare. | Handicare 1000 manualp.26 |
| H | The main power relay closed too early. | No owner check given. | Call Handicare. | Handicare 1000 manualp.26 |
| L | The current limit has been exceeded; the tile pictures a heavy load on the seat, and TechTool reads L as overloaded. | Take weight off the lift. | Still showing: call Handicare. | Handicare 1000 manualp.26 |
| n | The lift is driving at half speed. | No owner check given. | Telephone on the tile: call Handicare. | Handicare 1000 manualp.26 |
| o | The main control board has a memory problem. | No owner check given. | Call Handicare. | Handicare 1000 manualp.26 |
| r | A power supply fault during charging. | Check the on/off switch on the unit is on and the plug is in its socket; TechTool adds that every power switch should be on. | Both Handicare code pages say: if the action shown does not help, call Handicare, and write the code down first. | Handicare 1000 manualp.27 |
| U | A power supply fault while the battery is on float charge. | No owner check given. | Call Handicare. | Handicare 1000 manualp.27 |
| Y | A hardware fault on the main board. | No owner check given. | Call Handicare. | Handicare 1000 manualp.27 |
| . | | . | Over current: the display shows both upright pairs lit with a dot each side. | No owner check given. | Call Handicare. | Handicare 1000 manualp.27 |
| .8. | Sleep mode. | Use the toggle, or a button on a remote, to wake it. | If it will not wake, call Handicare. | Handicare 1000 manualp.27 |
Codes 3 to 6 depend on which side of the stairs the lift is fitted: the manual marks them LH and RH.
The 0 on a 1000
On the 1000, 0 covers three things: the key switch is off, the stop button has been pressed, or the seat is swivelled and not locked (Handicare 1000 manualpp.18-19). The manual says to turn the key ninety degrees clockwise; TechTool's 1000 page says to try turning it anti-clockwise. The picture in the manual marks the ON position, so turn it there. A lit stop button needs one press; the seat turns back with the handle under it until it clicks.
Switching on, and the reset
With nothing on the display and nothing moving, the manual says the lift may simply be switched off (p.21). TechTool puts the on/off button on the front of the lift and warns the footrest may need lowering to reach it; if the lift is already on, it may be asleep, and the toggle wakes it.
The manual's reset is printed under the code table. If the display shows anything other than the codes listed, drive the lift off the charge contacts, then turn the main switch on the unit off for 10 seconds and back on (Handicare 1000 manualp.27). TechTool gives a similar reset, the main power switch off for 10 to 15 seconds, for a remote that will not work while the joystick does, and for a powered footrest, swivel or slide track that has stopped. See how to reset a stair lift.
Stopping part way
If the 1000 will go only one way and shows 4 or 6, something is between the lift and the stairs: drive it the other way and take the obstacle out (p.21). L means the current limit has been exceeded, which the manual pictures as a heavy load on the seat and TechTool reads as overloaded. The manual's emergency pages describe a hand winder and a way to turn a powered seat by hand with a coin; this guide leaves both to an engineer.
If someone is stuck on the lift
Call 999 if they are hurt or cannot get off safely. Otherwise follow stuck on the stairs.
Remote controls
The 1000's wall-mounted remotes work by radio. The manual says a remote whose light shines red when pressed, with the lift not moving, has flat batteries (p.20). TechTool's check is whether the light shines at all: if not, replace the batteries the right way round. C on the display, an infrared address fault, is one for Handicare. More on remotes.
The manual
Handicare's 1000 user manual, rev. 15, covers the Smart, Smart XL and Smart XXL seats and is linked from TechTool's 1000 page; English is printed pages 1 to 28. The manual finder links it, and the Handicare page sets the 1000's codes beside the 1100's.
Where this comes from
Each meaning, check and number above is taken from the documents listed here, opened on the maker's own website. Page numbers in the text are the numbers printed in each manual. How the makers' documents are checked.