Beeps and alarms

Stairlift beeping: what each make's beeps mean

Stairlift beeping while the lift is parked almost always means it is not charging. Every maker read for this guide says so in its own way: Stannah calls it batteries not being charged, Acorn shows A1 and then goes to sleep, and Handicare shows a 2 or flashes a lamp. The fix is usually to get the chair onto its charge point with the power on. Some beeps are meant to happen, though, and a few mean an engineer.

Last checked: , against the makers' own documents Published by SEO Dons Ltd

Beeps that are meant to happen

  • Acorn 130: one beep as the lift parks on a charge point, and a beep each time the armrest paddle is pressed to show the command was received (Acorn 130 manualpp.11, 18).
  • Handicare Freecurve: three beeps when you move the joystick, before it gently sets off (Freecurve manualp.6).
  • Stannah with a powered hinged rail: beeps and a flashing light while the hinged rail moves, to warn people nearby (Stannah 260 guidep.13).
  • Brooks: a beep to say it is about to start a journey, which Brooks calls the loudest noise the lift makes (Brooks questionsweb page).

Beeps that mean it is not charging

Warning beeps as each maker's manual describes them
Make and modelWhat you hear and seeWhat the maker says to check
Stannah 260 and 420Beeping while parkedWall switch on, no power cut, chair at the very top or bottom (260); hinged rail sent fully up (420)
Stannah 600Code 1 on the display: charging or battery faultWall switch and master power switch on; no power cut
Acorn 130A1 and beeping; then about 60 seconds of beeps and sleep mode, with two beeps roughly every 40 secondsDrive to a charge point; mains not switched off; wake it with the paddle or remote
Acorn 180A1 flashing and beeping; then hibernation, a beep every 20 seconds and a dark displayMains on; parked on its charge points
Handicare 110040 seconds of beeps and a 2Plug in the socket; every power switch on
Handicare 100015 seconds of beeps and a 2Onto a charge point, or plug back in
Handicare FreecurveThree minutes of beeps, armrest lamp flashingOnto a charge point at the top or bottom, or plug back in

Pages: Stannah 260 guide p.25, Stannah 420 support page, Stannah 600 support page; Acorn 130 manual pp.24 and 22; Acorn 180 manual pp.11, 16 and 20; Handicare 1100 manual p.21; Handicare 1000 manual p.8; Freecurve manual pp.10 and 23.

Why is my stairlift beeping? Five checks

  1. Is it on its charge point? Curved lifts charge only at set points, usually the top and bottom; Stannah says a straight stairlift charges wherever it stops on the rail (Stannah beeping pageweb page). A chair stopped just short of the end will beep. Stannah's fix is to press the wall control towards that end so the lift finishes its travel.
  2. Is the socket switched on? Stannah, Acorn and Handicare all want the lift's supply left on. Acorn asks for a socket of its own; Handicare says never to unplug it.
  3. Has the power gone off? A power cut stops the charging, and the lift beeps as it would off its charge point.
  4. Are the lift's own switches on? Acorn's 130 has a battery isolation switch that must stay on; Stannah has a master power switch; Handicare's 1000 has an on/off button on the front.
  5. Is a hinged rail down? On a Stannah with a hinged rail, a lift left at the bottom beeps because it may be blocking a doorway and is not charging. Send it up with the remote.

How to stop a stairlift beeping

The proper way is to fix what it is warning about; most of the beeps above stop as soon as the lift is charging again. Two makers give owners a way to quieten it while they wait for help. Stannah's 260 and 420 guides say turning the master power switch off silences the beeper, then call your supplier (Stannah 420 support pageweb page). Acorn's flat-battery alarm, F5, stops after one press of the armrest control or the remote (Acorn 130 manualp.27), and the lift should then go to a charge point.

Silencing is not fixing

With Stannah's master power switch off, the batteries do not charge. Stannah's own beeping page warns that a lift left switched off, or unable to charge, drains its batteries so they need replacing sooner.

Beeping after a power cut

A lift that beeps during or after a power cut is doing what it should: it is running on its batteries and telling you it cannot charge. Acorn's manuals say an Acorn will keep working for several journeys, then stop once the batteries are spent; the 180 manual adds that you should let the batteries recharge before using it again. Once the power is back and the chair is on its charge point, the beeping should stop. After a power cut has each maker's account.

When the beeping means an engineer

If the chair is on its charge point, the power is on and it still beeps, the makers' manuals stop giving owner checks. On an Acorn 130, a C7, C8 or C9 means a fault in the charger or battery, and Acorn sends you to its authorised dealer. On a Handicare 1000, an r or a U is a power supply fault. On a Stannah 600, code 1 that will not clear may be a battery charging fault, which Stannah's 600 page says needs a call-out. And a lift that keeps sliding back into its low-battery code after full charges may need new batteries. The codes are in the stair lift error code library; worn batteries are on battery problems; who replaces them is on battery replacement.

By make

Each make's own beeping page goes further: Stannah beeping and Acorn beeping, and the Handicare page for the 1100, 1000 and Freecurve. The repair quote form on this page asks for the make, the model and the beep, and SEO Dons Ltd replies by email.

Where this comes from

Each meaning, check and number above is taken from the documents listed here, opened on the maker's own website. Page numbers in the text are the numbers printed in each manual. How the makers' documents are checked.

Get a stair lift repair quote

For when the maker's manual says it is a job for an engineer. Give the make, the model and what the lift shows or does. Replies come by email, so this is not the way to get help for someone stuck on a lift now.

After you press send

  1. SEO Dons Ltd, which publishes Stairlift Support, receives what you send.
  2. Someone reads the make, the model and the fault, and replies by email.
  3. There is no obligation: asking does not commit you to any repair.
Add the model and the exact code, light or beep (optional)

Stairlift Support is published by SEO Dons Ltd, which has no engineers and no link to any stair lift maker. Answers come by email. Someone stuck on a stair lift who is hurt or in danger needs 999, not this form. How details are used: privacy notice.

Get a stair lift repair quote
Get a stair lift repair quote