Remote controls

Stairlift remote not working: the makers' checks

A stairlift remote not working is usually one of two things: flat batteries in the handset, or a lift that is not switched on. Stannah says dead batteries are the most common cause, and that its remotes will not work unless the power key is in and turned on. Each maker's handset takes different batteries and shows its battery state differently, so here is what each maker's own guide says to check.

Last checked: , against the makers' own documents Published by SEO Dons Ltd

First: is the lift itself switched on?

A remote only tells the lift what to do; if the lift is off, nothing happens. Stannah's remote page says to check the power key is in and switched to on before anything else, because neither the lift nor the remotes work otherwise (Stannah remote pageweb page). Its 600 guide adds that the on/off switch must be on too. Acorn's 180 manual says the lift must be switched on, with the seat facing forward, before the remotes will work (Acorn 180 manualp.15). Handicare's TechTool runs through the same ground: the lift asleep, the key off, the emergency stop lit.

Batteries and lights, make by make

Remote handsets: batteries and what the lights mean
ModelBatteryWhat the light tells youSource
Stannah 600, 260, 420Three AA per remote; about a year with average useLights rotating: fine. On all the time: low. None: flat. With a hinged rail (260): flashing green means lowStannah guidesp.19
Acorn 130Replace yearly, Acorn recommendsNot described; the handset must point at an infrared sensor on the carriageAcorn 130 manualpp.12, 21
Acorn 180One 9 volt PP3; replace yearlyNot describedAcorn 180 manualp.15
Handicare 1100Not statedThe 2020 manual: red when pressed means flat batteries. TechTool: no red light means replace the batteriesHandicare 1100 manualp.21
Handicare 1000Not statedThe manual: red when pressed means flat batteries. TechTool: no light means replace themTechTool 1000web page
Handicare FreecurveNot statedNo light when pressed: flat batteries. Flashing twice a second: the lift is out of order, or stopped away from a charging stationFreecurve manualpp.23, 25

Changing the batteries

Changing a handset's batteries is the one battery job makers give to owners. Stannah's guides say to remove the screw, slide the battery cover down, open it and fit three new AA batteries; its remote page says to have three new ones ready, and that if the remote still does not work afterwards you should contact your local service branch. Acorn's 180 manual shows its PP3 battery cover sliding off the back of the handset, and warns that a battery fitted the wrong way round can damage the remote. Handicare's TechTool says simply to replace the batteries and make sure they are fitted correctly (Handicare TechTool, 1100web page). Acorn asks for old handset batteries to go to a recycling centre or a collection point in a shop.

When the batteries are fine

Acorn: interference and pairing

Acorn's handsets use infrared, and the 130 manual names two things that can upset them. Interference from outside sources can stop the lift part way, which Acorn calls a normal safety feature: release the button and press it again. And some low-energy light bulbs give off infrared light; if one is interfering, Acorn recommends changing it for a standard bulb (Acorn 130 manualp.21). The same page describes re-programming a handset that has lost its programming; because it involves pressing a safety edge on the carriage, this guide does not set it out. Follow Acorn's page exactly or ask an engineer.

Handicare: a reset, and the codes

For a 1000 whose remote has stopped but whose joystick still works, TechTool suggests switching the main power switch off for 10 to 15 seconds and back on. The 1100's display shows Ir or rF when a remote has been registered with it, and the 1000's shows C for an infrared address fault, which is one for Handicare.

Stannah: the wall controls

Stannah's remote calling controls stop the lift as soon as the arrow is released, and it will not start again for a few seconds; that pause is deliberate. Replacement or extra remotes come from your local service branch.

Still not working

If the lift runs from its own armrest control but no remote moves it, and new batteries have made no difference, the handset or the lift's receiver needs an engineer. If the lift does not run from the armrest either, the problem is not the remote: start with the switches and the code on the symptom finder, or the error code library. Brooks says its lifts come with two wireless remotes, and its site publishes no remote troubleshooting. The repair quote form at the foot of this page reaches SEO Dons Ltd, which replies by email.

Where this comes from

Each meaning, check and number above is taken from the documents listed here, opened on the maker's own website. Page numbers in the text are the numbers printed in each manual. How the makers' documents are checked.

Get a stair lift repair quote

For when the maker's manual says it is a job for an engineer. Give the make, the model and what the lift shows or does. Replies come by email, so this is not the way to get help for someone stuck on a lift now.

After you press send

  1. SEO Dons Ltd, which publishes Stairlift Support, receives what you send.
  2. Someone reads the make, the model and the fault, and replies by email.
  3. There is no obligation: asking does not commit you to any repair.
Add the model and the exact code, light or beep (optional)

Stairlift Support is published by SEO Dons Ltd, which has no engineers and no link to any stair lift maker. Answers come by email. Someone stuck on a stair lift who is hurt or in danger needs 999, not this form. How details are used: privacy notice.

Get a stair lift repair quote
Get a stair lift repair quote