Handicare Freecurve · curved stairs

Handicare Freecurve troubleshooting

Handicare Freecurve troubleshooting is done by reading a small lamp on the armrest, because the Freecurve has no code display. Handicare's English Freecurve manual (11P00404_F) and its TechTool fault-finder say what the lamp means when it is dark, faint, lit, flashing, or flashing with beeps, and what an owner can check for each. If none of those checks works, Handicare's answer is to call it.

Last checked: , against the makers' own documents Not affiliated with any manufacturer

What the lamp should do

Turn the key a quarter turn clockwise and the lamp on the armrest glows faintly: the lift is on (Freecurve manualp.6). Move the joystick and the lamp lights fully, the lift beeps three times and then sets off gently. So three beeps at the start of a journey are normal, and so is a faint lamp at rest.

When the lamp or the beeps say something is wrong

The armrest lamp stays dark when you push the joystick

What the maker says it means: The key switch is off.

  • Turn the key a quarter turn clockwise; the lamp should glow faintly (page 6). TechTool says to try the toggle first, then turn the key.

If that does not work: If the lamp stays dark with the key on, call Handicare.

Handicare Freecurve manualp.22

The lamp lights when you push the joystick, but nothing moves

What the maker says it means: An armrest is not folded down. TechTool adds the optional seatbelt, if fitted, must be fastened.

  • Fold both armrests fully down and fasten the belt if the lift has one.

If that does not work: Still not moving: call Handicare.

Handicare Freecurve manualp.22

The lamp flashes and the lift will not go either way

What the maker says it means: The seat has been swivelled and is not locked.

  • Turn the seat back to straight with the handle under the seat.

If that does not work: If that does not free it, call Handicare.

Handicare Freecurve manualp.21

The lamp flashes and the lift will only go one way

What the maker says it means: Something is caught between the lift and the stairs.

  • Move the lift the opposite way, then remove the obstacle.

If that does not work: Stopping again with nothing in the way: call Handicare.

Handicare Freecurve manualp.20

The lamp flashes and the stop button is lit

What the maker says it means: The emergency stop button has been pressed.

  • Press the stop button once to release it.

If that does not work: If it will not release, call Handicare.

Handicare Freecurve manualp.21

Beeping for three minutes with the lamp flashing

What the maker says it means: The batteries are not recharging: the lift is not sitting properly on a charge point, or its plug is out of the socket.

  • Send the lift to a charge point at the top or bottom of the rail; with the remote, hold the button until it stops there by itself.
  • Check the plug is in the wall socket. Handicare says never to unplug it.
  • TechTool: a lamp on the charging cable box shows orange while charging and green when full; allow two hours for a full charge.

If that does not work: If it still will not charge, call Handicare.

Handicare Freecurve manualpp.10, 23

The remote's lamp stays off when you press it

What the maker says it means: The handset's batteries are flat. TechTool also checks the lift's key switch is on.

  • Replace the remote's batteries, the right way round, and make sure the key on the lift is turned on.

If that does not work: No better with new batteries: call Handicare.

Handicare Freecurve manualp.23

The remote's lamp flashes twice a second

What the maker says it means: Pressing the remote: the lift is out of order and cannot set off. Not pressing it: after a journey, two flashes a second for 20 seconds mean the lift has stopped somewhere that is not a charging station.

  • TechTool: let the battery charge for two hours and call the lift again; clear any obstacle; turn the seat straight; press the emergency stop button once.

If that does not work: If it still flashes, call Handicare.

Handicare Freecurve manualp.25

Charging and the three-minute beep

The Freecurve charges at charge points at the top and bottom of the rail, and there may be more (Freecurve manualp.10). To park it, hold the remote's button until the lift reaches a charge point; it stops by itself and the remote's lamp goes out. If it stops short of the right position, it beeps for three minutes and the armrest lamp flashes. The manual says the lift does not work once its batteries are flat, so a beeping Freecurve needs moving or plugging in before it runs down. TechTool adds a lamp on the charging cable box: orange while charging, green when the battery is full, with about two hours for a full charge (Handicare TechTool, Freecurveweb page).

Two of the manual's reminders protect the batteries: never take the lift's plug out of the wall socket, and never remove the locking pin from the key switch. Take the key itself out when you leave the lift.

Handicare Freecurve battery replacement

The Freecurve manual does not describe changing the lift's batteries, and its guarantee excludes them. Handicare's fault pages end in the same place every time: if the check does not help, call Handicare. Battery replacement explains what other makers say.

The folding hinge

Some Freecurves have a hinged section of rail at the foot of the stairs. When the hinge is not working, the manual says the lift can still ride upwards. TechTool's advice for a hinge fault is to call an engineer, and it describes one owner step for someone sitting on the lift at the hinge point: hold the toggle in the up direction, and after about 15 seconds the lift travels to the top of the stairs so they can get off safely. TechTool calls this a safety override that works in the upward direction only, to stop anyone being trapped. The manual also shows how the hinge can be folded by hand in an emergency; this guide leaves that to an engineer.

Resetting a Freecurve

The Freecurve manual is clear: only in an emergency, and only by a certified engineer (Freecurve manualp.28). There is no owner reset to try. Its emergency page for the seat is also left to an engineer here. How to reset a stair lift shows which makers do give owners a reset.

Someone stuck on the lift and hurt: call 999

For everything else about a lift that has stopped with someone on it, see stuck on the stairs.

The remote control's lamp

The manual's remote table explains the small lamp on the Freecurve's handset (Freecurve manualp.25). It stays off for the first three seconds while the lift starts up, comes on while it travels, and goes out when it stops at a charging station or at an end stop. Flashing twice a second while you press it means the lift is out of order and cannot set off. Flashing twice a second for 20 seconds after you let go means it has stopped somewhere that is not a charging station. A lamp that does not light at all usually means flat batteries in the handset. More on remotes.

The manual

The Freecurve manual that TechTool's Freecurve page links has no English text, only headings. The English edition, 11P00404_F, is on the same Handicare site, and that is the one used here; the manual finder links it. Other Handicare models are on the Handicare page.

Where this comes from

Each meaning, check and number above is taken from the documents listed here, opened on the maker's own website. Page numbers in the text are the numbers printed in each manual. How the makers' documents are checked.

Get a stair lift repair quote

For when the maker's manual says it is a job for an engineer. Give the make, the model and what the lift shows or does. Replies come by email, so this is not the way to get help for someone stuck on a lift now.

After you press send

  1. SEO Dons Ltd, which publishes Stairlift Support, receives what you send.
  2. Someone reads the make, the model and the fault, and replies by email.
  3. There is no obligation: asking does not commit you to any repair.
Add the model and the exact code, light or beep (optional)

Stairlift Support is published by SEO Dons Ltd, which has no engineers and no link to any stair lift maker. Answers come by email. Someone stuck on a stair lift who is hurt or in danger needs 999, not this form. How details are used: privacy notice.

Get a stair lift repair quote
Get a stair lift repair quote