Resets and restarts

How to reset a stairlift, make by make

How to reset a stairlift depends entirely on the make, and some makers do not give owners a reset at all. Acorn's 130 manual uses its battery isolation switch, off for 30 seconds. Stannah's guides restart the lift with the power key. Handicare's 1100 uses the key and its 1000 a main switch, while its Freecurve manual says only a certified engineer should reset it. Below is each maker's own method, and the codes for which a reset is the wrong move.

Last checked: , against the makers' own documents Published by SEO Dons Ltd

The resets makers publish

Owner resets and restarts, as each maker prints them
ModelThe maker's resetSource
Acorn 130Battery isolation switch off, wait 30 seconds, back on. Resets the control board and clears the codes on the display.130 manualp.22
Acorn 180None in the user manual.180 manualwhole manual
Stannah 600No timed reset. If the lift still will not move: take the power key out and put it back, then hold the control downwards; it should start after a few seconds.600 guidep.23
Stannah 260 and 420Turn the power key off, then back on, then hold the control downwards. The 260 checklist also has turning the on/off switch off and on.260 guidep.24
Handicare 1100 (installed before May 2024)The key switch under the arm: off, wait 30 seconds, back on.TechTool 1100web page
Handicare 1100 (installed after May 2024)TechTool's steps include removing a cover to reach a switch: not set out here.TechTool 1100web page
Handicare 1000Drive the lift off the charge contacts, then the main switch on the unit off for 10 seconds and back on.1000 manualp.27
Handicare FreecurveOnly in an emergency, and only by a certified engineer.Freecurve manualp.28

How to reset an Acorn stairlift

On the straight Acorn 130, the battery isolation switch sits on the wall side edge or the rear of the carriage cover (Acorn 130 manualp.10). Acorn's reset is to switch it off, leave it for 30 seconds and switch it back on; the manual says this resets the control board and clears the fault codes on the display. Its code table calls for the reset on three fatal errors (F1 relay, F2 brake, F3 motor overcurrent), and for F2 adds an hour on a charge point afterwards. Two cautions come from the same manual. The switch must be left on at all other times, or the batteries lose their charge. And if a code comes back after the reset, the next step is the dealer.

The curved Acorn 180's manual gives no reset. Its owner checks are the mains, the charge points, the seat and anything in the way, and after those, the authorised dealer. Acorn's codes, with the reset rows marked, are on Acorn error codes.

How to reset a Stannah stairlift

Stannah's guides do not have a reset in the Acorn sense, with a timed power-off. What they have is a restart for a lift that will not move, and it uses the power key. On a 600, take the key out and put it back in; on a 260 or 420, turn it off and back on. Then push and hold the control in the downward direction; after a few seconds the lift should start (Stannah 260 support pageweb page). If it stops again, repeat until you reach the bottom, then call your Stannah branch and ask for an engineer.

Stannah's checklist for a 260 with its power light on also includes turning the on/off switch off and back on. If it beeps when switched back on, the guide says to contact your supplier rather than try again. Model pages: Stannah 600, Stannah 260, Stannah 420.

How to reset a Handicare stairlift

Handicare's owners' site, TechTool, asks when an 1100 was installed before it gives a reset. For lifts installed before May 2024 the reset is the key switch under the arm: off, 30 seconds, on (Handicare TechTool, 1100web page). For later lifts, its steps include unplugging the lift and removing a cover to reach an on/off switch underneath; this guide does not relay steps that open a cover, so ask Handicare to talk you through it, or ask an engineer.

The Handicare 1000 manual prints its reset under the code table: if the display shows anything that is not one of its listed codes, drive the lift off the charge contacts, turn the main switch on the unit off for 10 seconds and back on (Handicare 1000 manualp.27). TechTool's 1000 pages use the same main-switch reset, for 10 to 15 seconds, when a remote has stopped working but the joystick still works, and when a powered footrest, swivel or slide track has stopped. The Freecurve is the exception: its manual says a reset is for emergencies only and is done by a certified engineer. More on the Handicare page.

When a reset is the wrong move

  • When the code says call. Acorn's H1, H2, F6 and F7; Handicare's d, o, Y and the other codes whose tile shows a telephone; Stannah's 9 or F. A reset does not fix these, and the maker's answer is an engineer.
  • When the code comes straight back. One reset, done the maker's way, is the limit. Acorn and Handicare both send you to the dealer if it does not clear.
  • When the problem is power or position. A lift that is off its charge point, unplugged or switched off at the wall will not be helped by a reset: see battery problems first.
  • When it means opening the lift. If the only switch you can find is behind a cover, leave it.

Someone is on the lift and it has stopped

The person comes first. If they are hurt or cannot get off safely, call 999. Use only the maker's own restart, from the seat, if they are safe. Stuck on the stairs has each maker's advice.

Before you reset: write down what it showed

A reset clears the display, so note the code, light or beep first. Handicare's code pages ask you to write the code down before you call; Stannah's guides ask for the model number from the lift's label. The stair lift error code library may answer it before you need to reset at all, and the repair quote form at the foot of this page asks for the same details.

Where this comes from

Each meaning, check and number above is taken from the documents listed here, opened on the maker's own website. Page numbers in the text are the numbers printed in each manual. How the makers' documents are checked.

Get a stair lift repair quote

For when the maker's manual says it is a job for an engineer. Give the make, the model and what the lift shows or does. Replies come by email, so this is not the way to get help for someone stuck on a lift now.

After you press send

  1. SEO Dons Ltd, which publishes Stairlift Support, receives what you send.
  2. Someone reads the make, the model and the fault, and replies by email.
  3. There is no obligation: asking does not commit you to any repair.
Add the model and the exact code, light or beep (optional)

Stairlift Support is published by SEO Dons Ltd, which has no engineers and no link to any stair lift maker. Answers come by email. Someone stuck on a stair lift who is hurt or in danger needs 999, not this form. How details are used: privacy notice.

Get a stair lift repair quote
Get a stair lift repair quote