Stopping and not moving

Stairlift keeps stopping: what the manuals say

A stairlift that keeps stopping is, most of the time, doing exactly what it was built to do. Every lift in this guide has safety edges or sensors on the footrest and carriage that stop it the moment they touch something, and a seat or arm that is out of position stops it too. Each maker's manual says how to tell which, and what an owner may do: move the lift back the other way and take the obstruction out. If it keeps stopping with nothing there, the manuals say it is time for an engineer.

Last checked: , against the makers' own documents Published by SEO Dons Ltd

Why stair lifts stop: the safety edges

The edges are pressure-sensitive strips around the footrest and the carriage, the box that runs along the rail. Acorn's 180 has five: one on each side of the carriage, one on each side of the footrest and one under it (Acorn 180 manualp.12). Acorn's 130 lists upper and lower safety pads on the carriage and upper and lower edges on the footrest. Brooks describes five sensors, three on the footrest and two on the carriage, which halt the lift if anything blocks it (Brooks featuresweb page). When one is pressed, the lift stops at once and usually will travel only away from whatever it touched.

What each lift shows when an edge stops it

How each model reports an obstruction
ModelWhat it showsThe maker's check
Acorn 130E1, E2 (footrest edges), E4, E5 (carriage edges); F8 or F9 if an edge is pressed at the top or bottom stopMove the lift back the opposite way and remove the obstruction (p.22)
Acorn 180E1 to E5, one for each of its five edgesMove it back the opposite way and remove the obstruction (p.12)
Stannah 600Code 3: obstruction around the footrest or carriageWith it switched on, move it the opposite way, remove the obstruction, carry on
Stannah 260, 420Power light on, but it will not moveNothing obstructing the safety edges; move it the opposite way to clear it
Handicare 1100, 10004 or 6, and it travels one way onlyMove it in the opposite direction and remove the obstacle (1100 p.22; 1000 p.21)
Handicare FreecurveArmrest lamp flashing, travels one way onlyMove it the other way and remove the obstacle (p.20)

Stops that are not obstructions

If nothing is in the way, look at the seat, the arms and the belt. Acorn, Stannah and Handicare lifts all stay put while the seat is swivelled out of its travelling position: Acorn shows E6, Stannah's 600 shows 7, Handicare a dash or a 0. Acorn's and Stannah's lifts will not run with an arm raised (Stannah 600 code 5), and some Stannah lifts will not start until an immobiliser seatbelt is fastened (code 6). On a Handicare, a lit emergency stop button holds the lift until it is pressed again. And on a lift with a hinged rail, a folded hinge stops it: Handicare's 1100 manual says the lift can still travel upwards from there (Handicare 1100 manualp.12).

Stopping and starting: often the battery

A lift that stops after a short distance and then carries on, or slows as it climbs, is showing one of Stannah's signs of a battery running out (Stannah batteries pageweb page). Acorn's lifts refuse to go up at all with a low battery (E7), and Handicare's 1100 shows a 7 when the voltage is too low to ride. Check the lift has been charging, then see battery problems.

Stopping short of the top

Stannah's beeping page answers this one directly: first look for objects or blockages and remove them, then check the rail is clean, dry and not over-lubricated, and that any hinged rail is in the right position (Stannah beeping pageweb page). It says you can wipe the rail with a lightly damp cloth if you feel safe doing so. Other makers' care advice differs: Acorn's 130 manual wants a dry cloth and no damp cloth with abrasive cleaner, and Handicare's 1100 manual says never to grease its friction-drive rail. Follow your own model's guide.

Never make a safety edge stop working

Do not press, hold, tape or adjust an edge to make the lift move, and do not take any part off to look underneath. Acorn's 130 manual says that if you think something has fallen down the rail into the mechanism, consult your Acorn representative before using the lift again (Acorn 130 manualp.5).

When it keeps stopping with nothing there

That is where the owner checks end. A lift that stops repeatedly with the stairs clear, the seat locked, the arms down and the battery charged needs an engineer to look at the edges, sensors and drive. Note the code or the light each time it happens, and where on the stairs. If someone is on the lift when it stops, see stuck on the stairs first. The codes are in the error code library, and the repair quote form at the foot of this page reaches SEO Dons Ltd, which replies by email.

Where this comes from

Each meaning, check and number above is taken from the documents listed here, opened on the maker's own website. Page numbers in the text are the numbers printed in each manual. How the makers' documents are checked.

Get a stair lift repair quote

For when the maker's manual says it is a job for an engineer. Give the make, the model and what the lift shows or does. Replies come by email, so this is not the way to get help for someone stuck on a lift now.

After you press send

  1. SEO Dons Ltd, which publishes Stairlift Support, receives what you send.
  2. Someone reads the make, the model and the fault, and replies by email.
  3. There is no obligation: asking does not commit you to any repair.
Add the model and the exact code, light or beep (optional)

Stairlift Support is published by SEO Dons Ltd, which has no engineers and no link to any stair lift maker. Answers come by email. Someone stuck on a stair lift who is hurt or in danger needs 999, not this form. How details are used: privacy notice.

Get a stair lift repair quote
Get a stair lift repair quote