Stannah · fault codes

Stannah stairlift error codes and lights

Stannah stairlift error codes are a model 600 feature. Its display panel, on the side of the carriage, shows a single number or letter: 2 when all is well, 1 and 3 to 7 for things an owner can usually check, and 9 or F when a service engineer is needed. Stannah's 260 and 420 guides have no codes at all; on those lifts the power light and the lift's behaviour are the clues. Codes 8 and H appear in no Stannah guide this site has read.

Last checked: , against the makers' own documents Not affiliated with any manufacturer

The codes people look up

Searched Stannah codes, read against the 600 guides and Stannah's 600 support page
CodeOn a Stannah 600
1 Charging or battery fault
2 No fault found
3 Something at the footrest or carriage
4 Power key or on/off switch
5 Seat sensor or downside arm
8 Not in any 600 guide or on Stannah's 600 support page
9 Engineer needed
H Not in any 600 guide or on Stannah's 600 support page

Model 600: every code, with Stannah's checks

The three 600 guides (Siena, Starla and Sofia or Solus, all Issue 7, November 2022) share one table on page 22, and Stannah's 600 support page adds detail to most rows (Stannah 600 support pageweb page). Stannah's own summary of the codes is that they let owners identify, and in most cases fix, common problems without calling out an engineer.

Stannah 600 display codes, from the 600 guides and Stannah's 600 support page
Shows What the maker says it means What the maker lets you check When it needs an engineer Where it says so
1 A charging or battery fault. The guide prints the code as "-/1". Make sure the wall switch is on, and the master power switch too (Stannah's 600 page says both should always be left on), and that there has not been a power cut. If it persists, call your Stannah supplier. Stannah's 600 page says that with the switch on and no power cut it may be a battery charging fault needing a call-out. Stannah 600 guidep.22
2 The lift has found no fault and is in normal operation. No owner check given. If the lift still will not work while 2 shows, call your Stannah supplier or local service branch. Stannah 600 guidep.22
3 The safety edges have detected an obstruction around the footrest or the carriage. With the lift still switched on, move it back in the opposite direction, remove what is in the way, then carry on up or down. Stannah gives no further step; if code 3 keeps returning with nothing in the way, call your supplier. Stannah 600 guidep.22
4 The power key is not in properly, or the on/off switch is off. Push the power key fully into its keyhole and put the on/off switch on; the light on the switch should come on (Stannah's 600 page, and page 10 of the guide). The guide's answer for code 4 is to call your Stannah supplier; the 600 page says to contact your local branch if the key and switch checks do not clear it. Stannah 600 guidep.22
5 The seat sensor is not detecting anyone sitting, or the arm on the downhill side is not lowered. The Siena guide gives only the arm. Lower the seat and both arms fully, then try again (Stannah's 600 page). Not cleared: the guides say call your Stannah supplier; the 600 page says your local branch. Stannah 600 guidep.22
6 On a lift with the optional immobiliser seatbelt, the belt is not fastened properly, and the lift will not start until it is. Click the seatbelt fully into its buckle (page 14). Stannah gives no further step; if the belt is fastened and 6 remains, call your supplier. Stannah 600 guidep.22
7 The seat is swivelled out of the position it travels in. Swivel the seat fully back to its travelling position (page 6 of the guide). Stannah gives no further step; if 7 will not clear, call your supplier. Stannah 600 guidep.22
9 or F The lift is asking for a service engineer. No owner check given. Call your Stannah supplier or local service branch: there is no owner check for this one. Stannah 600 guidep.22

Code 3 and code 4, the two most searched

3 is the safety edges doing their job: something is against the footrest or the carriage. Stannah's support page says to check for the obstruction and, with the lift still switched on and you in the seat, move it back the way it came so you can remove what is there, then carry on. It adds a habit worth keeping: small items can get stuck, so keep the track clear of clutter.

4 is the power key or the on/off switch. The guide's table answers it with "call your Stannah supplier", but the support page first asks you to push the key fully into its keyhole and turn the on/off switch on, when the switch's light should come on (600 Siena guidep.10). On a Sofia or Solus chair the key goes into the end of the control pod and turns to on, and a green light on the armrest shows it is on.

Flashing and steady lights

"Stannah stairlift light flashing" can mean several different lights, and only one of them is a fault code.

Stannah 600 status light, as the Starla guide explains it
Shows What the maker says it means What the maker lets you check When it needs an engineer Where it says so
LED off In the Starla guide's status lights, no light means the master power switch is off. Switch the master power switch on: page 9 of the guide shows it on the back of the base of the chair. Stannah gives no further step; if the light stays off with the switch on, call your supplier. Stannah 600 guidep.22
LED pulsing A pulsing light means the power key is not in properly or the on/off switch is off. (Page 10 notes the light also pulses when the lift is switched off with the key left in.) Push the key fully in and turn the on/off switch on. Still pulsing with both done: call your supplier. Stannah 600 guidep.22
LED on A steady light means the stairlift is ready to move. No owner check given. Nothing to fix: Stannah lists this as ready. Stannah 600 guidep.22
  • The power light on a 260 or 420. Off means the master power switch or the power key is off; on means power is reaching the chair. The 260 guide adds that turning the on/off switch off and on and hearing a beep means call your supplier (260 Siena guidep.24).
  • A light flashing on the hinged rail. The guides say a light flashes and the lift beeps while a powered hinged rail is moving: a warning, not a fault.
  • The lights on a remote calling control. Rotating means its batteries are fine, on all the time means they are low, and none means flat. On a 260 with a hinged rail, Stannah's 260 page says a flashing green light means low batteries.

The 260 and 420: no codes, a checklist instead

Stannah's guides for the curved 260 and for the 420 replace the code table with two checklists: one for a lift that will not move, split by whether the power light is on or off, and one for a lift that beeps (420 Starla guidepp.22-23). Both models have their own pages: Stannah 260 and Stannah 420.

When to ring, and what to say

Code 9 or F has no owner check: Stannah's answer is to contact your local service branch. For every other code, Stannah's table gives a check first and a call second. When you call, have the code, the model number from the label on the carriage, and a short account of what the lift was doing (600 Siena guidep.24). The repair quote form on this page asks for the same things. Codes from other makers are in the stair lift error code library, and beeps are on Stannah beeping.

Where this comes from

Each meaning, check and number above is taken from the documents listed here, opened on the maker's own website. Page numbers in the text are the numbers printed in each manual. How the makers' documents are checked.

Get a stair lift repair quote

For when the maker's manual says it is a job for an engineer. Give the make, the model and what the lift shows or does. Replies come by email, so this is not the way to get help for someone stuck on a lift now.

After you press send

  1. SEO Dons Ltd, which publishes Stairlift Support, receives what you send.
  2. Someone reads the make, the model and the fault, and replies by email.
  3. There is no obligation: asking does not commit you to any repair.
Add the model and the exact code, light or beep (optional)

Stairlift Support is published by SEO Dons Ltd, which has no engineers and no link to any stair lift maker. Answers come by email. Someone stuck on a stair lift who is hurt or in danger needs 999, not this form. How details are used: privacy notice.

Get a stair lift repair quote
Get a stair lift repair quote