The codes people search for, on each model
A1, C4, E7 and E9 are the codes most often typed into a search box after "Acorn stairlift". This table puts each beside its meaning on the 130 and on the 180. Where a model's manual does not contain the code, it says so: that is not a fault-free answer, it means Acorn has published nothing for that code on that lift.
| Code | On the Acorn 130 | On the Acorn 180 |
|---|---|---|
| A1 | Not charging, beeping (p.24) | Ready, not charging (p.16) |
| A2 | Going up (armrest) (p.25) | Going up (arm switch) (p.16) |
| C1 | Charging (p.24) | Charging (p.16) |
| C4 | Charging (p.24) | Fully charged (p.16) |
| E3 | Not in the 130 manual | Under-footrest edge (p.16) |
| E5 | Carriage edge, up side (p.25) | Carriage edge, up side (p.16) |
| E6 | Seat not in riding position (p.25) | Seat swivelled (p.16) |
| E7 | Battery low (p.26) | Battery low (p.16) |
| E9 | Key switch off (p.26) | Not in the 180 manual |
| F5 | Battery flat, alarm (p.27) | Battery flat, alarm (p.16) |
| F9 | Up-side edge at the bottom (p.27) | Not in the 180 manual |
| J3 | Not in the 130 manual | Not in the 180 manual |
C1 and C4 on the 130 fall inside its C1 to C5 charging count. J3 is in neither manual.
Acorn 130: the full table
The 130 manual groups its codes under five headings and says, for each heading, whether the lift will still run (Acorn 130 manualpp.24-27). Charging codes and standard operating codes leave it working; operating errors, hardware faults and fatal errors stop it. Read the right-hand columns before you do anything: where Acorn's printed remedy is a job inside the lift, the row says to call an engineer instead.
| Shows | What the maker says it means | What the maker lets you check | When it needs an engineer | Where it says so |
|---|---|---|---|---|
| C1-C5 | Parked on a charge point and taking charge. The number climbs from C1, the lowest level, to C5 as the batteries fill. | No owner check given. | Nothing to fix: Acorn lists this as normal running. | Acorn 130 manualp.24 |
| C6 | On a charge point with the batteries already full, so the charger is connected but has stopped putting charge in. | No owner check given. | Nothing to fix: Acorn lists this as normal running. | Acorn 130 manualp.24 |
| C7 | A fault: the charger is connected but the voltage it supplies is too low for it to charge as it should. | No owner check given. | The manual then sends you to an authorised Acorn dealer. | Acorn 130 manualp.24 |
| C8 | A fault: the charger is connected but its voltage is too high, so it is not charging correctly. | No owner check given. | The manual then sends you to an authorised Acorn dealer. | Acorn 130 manualp.24 |
| C9 | A fault: the charger is connected but no charge goes in, because the lift cannot find its battery or the battery has failed. | No owner check given. | The manual then sends you to an authorised Acorn dealer. | Acorn 130 manualp.24 |
| blank | Nothing on the display means either no power is reaching the lift or it has gone into sleep mode. | Make sure the battery isolation switch on the carriage is on (page 10 shows where), then press the armrest paddle to wake the lift. | Acorn gives no further step here; if the display stays blank, call an engineer. | Acorn 130 manualp.24 |
| A1 | The chair has been left somewhere off a charge point, so nothing is charging the batteries, and the lift beeps to tell you. | Drive the lift with the paddle until it reaches a charge point, and check that nobody has switched off the mains supply. | If A1 stays with the chair on a charge point and the power on, Acorn gives no further step: call an engineer. | Acorn 130 manualp.24 |
| A2 | Travelling upward because the armrest control is being held. | No owner check given. | Nothing to fix: Acorn lists this as normal running. | Acorn 130 manualp.25 |
| A3 | Travelling downward on the armrest control. | No owner check given. | Nothing to fix: Acorn lists this as normal running. | Acorn 130 manualp.25 |
| A4 | Travelling upward because a remote handset is being used. | No owner check given. | Nothing to fix: Acorn lists this as normal running. | Acorn 130 manualp.25 |
| A5 | Travelling downward on a remote handset. | No owner check given. | Nothing to fix: Acorn lists this as normal running. | Acorn 130 manualp.25 |
| A9 | The lift is working its folding hinge section of rail. Let it carry on until the hinge lines up with the rail or has folded right up. | No owner check given. | Nothing to fix: Acorn lists this as normal running. | Acorn 130 manualp.25 |
| E1 | The lift has stopped because the safety edge on the downhill side of the footrest, or the plate beneath it, has been pressed. | Look for something caught on that side of the footrest. Page 22 says moving the lift back the opposite way and clearing what is trapped can free it. | If that does not clear it, page 22 says to contact your authorised Acorn representative. | Acorn 130 manualp.25 |
| E2 | Stopped by the safety edge on the uphill side of the footrest. | Look for an obstruction on the uphill side of the footrest; reverse the lift and clear it, as page 22 describes. | Not cleared by that: contact your authorised Acorn representative (page 22). | Acorn 130 manualp.25 |
| E4 | Stopped by the safety edge on the downhill side of the carriage, the box that runs along the rail. | Check the downhill side of the carriage for anything in the way; move back and remove it (page 22). | Still showing after that: contact your authorised Acorn representative (page 22). | Acorn 130 manualp.25 |
| E5 | Stopped by the safety edge on the uphill side of the carriage. | Check the uphill side of the carriage for an obstruction and clear it after reversing the lift (page 22). | If E5 returns, contact your authorised Acorn representative (page 22). | Acorn 130 manualp.25 |
| E6 | The seat has been swivelled and is not locked in the position it travels in. | Turn the seat back until it locks in its riding position. | Acorn gives no further step; if E6 will not clear, call an engineer. | Acorn 130 manualp.25 |
| E7 | The batteries are low. The lift will still go down, but will not go up until they have recharged enough for the code to clear. | Use the directional toggle to take the lift down to the nearest charge point and leave it there to charge. | Acorn gives no further step; if E7 keeps coming back after full charges, call an engineer. | Acorn 130 manualp.26 |
| E9 | The key is out, or turned to off, so the lift will not run. | Put the key in and turn it to on. Page 10 says it turns to the right, clockwise. | Acorn gives no further step; if E9 stays with the key on, call an engineer. | Acorn 130 manualp.26 |
| H1 | The manual reports a fault where the first safety circuit (SW1) has a connection to the chassis. | No owner check given. | The step Acorn prints is an electrical continuity test on the safety circuit, which is not an owner check. Call an engineer. | Acorn 130 manualp.26 |
| H2 | The same fault on the second safety circuit (SW2). | No owner check given. | As for H1, the printed step is an electrical test: leave it to an engineer. | Acorn 130 manualp.26 |
| H3 | A fault: the lift cannot work its hinge section because the hinge is not communicating. | Check the mains supply to the lift has not been switched off or unplugged at the wall. | The manual then sends you to an authorised Acorn dealer. | Acorn 130 manualp.26 |
| H6 | A fault: the hinge section cannot get into line with the rail, or cannot fold all the way. | Look for anything obstructing the hinge section. | The manual then sends you to an authorised Acorn dealer. | Acorn 130 manualp.26 |
| F1 | One of the lift's fatal errors: a relay fault. | Reset the lift: switch the battery isolation switch off, wait 30 seconds and switch it back on (page 22). | If the reset does not clear it, the manual sends you to your authorised Acorn dealer. | Acorn 130 manualp.26 |
| F2 | A fatal error with the brake. | Reset (30 seconds off at the battery isolation switch), then drive the lift to a charge point and leave it charging for an hour. | Still there after that: your authorised Acorn dealer, says the manual. | Acorn 130 manualp.26 |
| F3 | A fatal error: the motor drew more current than it should. | Reset with 30 seconds off at the battery isolation switch. | Not cleared by a reset: contact your authorised Acorn dealer, as the manual says. | Acorn 130 manualp.27 |
| F5 | The batteries are very low and an alarm is sounding. | Press the armrest control or the remote once to silence the alarm. When E7 shows, bring the lift down to the nearest charge point to recharge. | Acorn gives no further step; if the batteries will not hold a charge, call an engineer. | Acorn 130 manualp.27 |
| F6 | The lift has travelled past the end-of-travel limit that should have stopped it. | No owner check given. | The manual's first step is hand winding (page 20). This guide does not set out hand winding: call an engineer. | Acorn 130 manualp.27 |
| F7 | The over-speed safety device has locked the lift to the rail. Page 19 says it can trip without a real fault after a hard knock or vibration. | No owner check given. | The manual resets it by hand winding (page 20), which this guide does not set out: call an engineer. | Acorn 130 manualp.27 |
| F8 | A safety edge on the downhill side of the carriage or footplate was pressed while the lift sat at its top stop. | Check that edge for something in the way and clear it. | Acorn gives no further step; if F8 stays, call an engineer. | Acorn 130 manualp.27 |
| F9 | A safety edge on the uphill side of the carriage or footplate was pressed while the lift was at its bottom stop. | Check that edge for an obstruction and remove it. | If F9 stays after that, Acorn gives no further step: call an engineer. | Acorn 130 manualp.27 |
Acorn 180: the full table
The 180's manual lists 18 symbols in one table and adds no headings (Acorn 180 manualp.16). Its safety-edge codes run to E5 because the curved lift has a fifth edge under the footrest, and its battery codes are the same pair as the 130's, E7 and F5. It has no H codes and no reset.
| Shows | What the maker says it means | What the maker lets you check | When it needs an engineer | Where it says so |
|---|---|---|---|---|
| blank | The display under the seat is dark because the lift is switched off or has gone to sleep. | To switch on, turn the key clockwise and push the switch until its green light shows (page 8). A sleeping lift wakes when you use the controls or a remote (page 20). | Still dark after that: Acorn gives no further step, so call an engineer. | Acorn 180 manualp.16 |
| A1 | The lift can be used but its batteries are not charging. Page 11 adds that A1 flashes and a beep sounds while this lasts. | Check the mains is switched on and the chair is parked on its charge points. | If A1 remains with both done, Acorn gives no further step: call an engineer. | Acorn 180 manualp.16 |
| A2 | Moving upward on the arm switch control. | No owner check given. | Nothing to fix: Acorn lists this as normal running. | Acorn 180 manualp.16 |
| A3 | Moving downward on the arm switch control. | No owner check given. | Nothing to fix: Acorn lists this as normal running. | Acorn 180 manualp.16 |
| A4 | Moving upward on a remote control. | No owner check given. | Nothing to fix: Acorn lists this as normal running. | Acorn 180 manualp.16 |
| A5 | Moving downward on a remote control. | No owner check given. | Nothing to fix: Acorn lists this as normal running. | Acorn 180 manualp.16 |
| A9 | The lift is waiting while its hinge operates. | No owner check given. | Nothing to fix: Acorn lists this as normal running. | Acorn 180 manualp.16 |
| C1 | The batteries are charging. | No owner check given. | Nothing to fix: Acorn lists this as normal running. | Acorn 180 manualp.16 |
| C4 | The batteries are full. (On the 180, C4 means full; on the 130 it is only a stage of charging.) | No owner check given. | Nothing to fix: Acorn lists this as normal running. | Acorn 180 manualp.16 |
| E1 | The sensitive edge on the downhill side of the footrest has been pressed. | Look for an obstruction. Page 12 says to move the lift back the opposite way and remove it. | Acorn gives no further step; if it keeps stopping with nothing in the way, call an engineer. | Acorn 180 manualp.16 |
| E2 | The sensitive edge on the uphill side of the footrest has been pressed. | Reverse the lift and clear whatever is in the way (page 12). | Nothing in the way and still stopping: call an engineer. | Acorn 180 manualp.16 |
| E3 | The sensitive edge underneath the footrest plate has been pressed. The 180 has five safety edges, and this is the fifth (page 12). | Check below the footrest for an obstruction; reverse and remove it. | If E3 stays with nothing there, call an engineer. | Acorn 180 manualp.16 |
| E4 | The sensitive edge on the downhill side of the lift has been pressed. | Look for an obstruction on the downhill side and clear it after reversing. | Recurring with nothing in the way: call an engineer. | Acorn 180 manualp.16 |
| E5 | The sensitive edge on the uphill side of the lift has been pressed. | Look for an obstruction on the uphill side, reverse and remove it. | If it will not clear, call an engineer. | Acorn 180 manualp.16 |
| E6 | The seat has been turned away from the position it operates in. | Swivel the seat back until it locks facing forward. | Will not clear: call an engineer. | Acorn 180 manualp.16 |
| E7 | Low batteries. Downward travel is allowed so you can reach a charge point; upward travel is blocked until they have recharged and the code has gone. | Bring the lift down to the nearest charging station. | If it keeps happening, call an engineer: page 11 says batteries that run too low have to be replaced by one. | Acorn 180 manualp.16 |
| F5 | The batteries are flat and an alarm sounds. | Press the arm switch control or the remote once to stop the alarm, then take the lift down to the nearest charging station. | Acorn gives no further step; if it will not recharge, call an engineer. | Acorn 180 manualp.16 |
| F7 | The 180 manual does not name this fault. It warns that the hand winder must not be turned in the down direction while F7 shows, as that could damage the lift. | No owner check given. | Contact your stairlift supplier straight away: the manual says immediately. | Acorn 180 manualp.16 |
Reading these tables safely
Three things in Acorn's tables are worth knowing before you act on a row. The first is that "NORMAL" in Acorn's headings means the lift is doing what it was designed to do, not that nothing needs doing: E1 to E9 on the 130 are all marked normal, yet each one stops the lift until its cause is dealt with. The second is that the owner checks are short on purpose. Switches, the key, the seat, the charge point and clearing an obstruction are the whole list; this guide adds nothing to it.
The third is the remedies we do not repeat. The 130's table answers H1 and H2 with an electrical continuity test, and F6 and F7 with hand winding (Acorn 130 manualp.27). Its page 22 also suggests tapping a trapped safety edge. Those rows here say call an engineer, because each means opening the lift or handling a safety device. The 180's F7 row is the plainest of all: do not hand wind it downwards, contact your supplier immediately.
Codes that are not in either manual
Searches for Acorn codes include some that neither public manual contains. J3 is one. On the 130, E3 and E8 are missing from the code pages; E8 appears only as a label on the wiring diagram, which is not a meaning for an owner. On the 180, anything outside the 18 symbols, including E9, the C codes other than C1 and C4, and the F codes other than F5 and F7, is unlisted. For any of these this guide gives no meaning: tell the dealer or an engineer the code and the model.
The Acorn 120 and older Acorn lifts
Acorn does not publish a user manual for the Superglide 120 on its website, and its owners' site keeps the full status-code list behind a sign-in. The Acorn 120 page explains what was checked and how to get the right answer. The same goes for any older Acorn lift whose manual is not among the two above: its codes are left unexplained here rather than borrowed from a 130 or a 180.
When the code means the dealer
Acorn's tables send you to an authorised Acorn dealer for the charging faults C7, C8 and C9, the hinge faults H3 and H6 after the simple checks, and the fatal errors F1, F2 and F3 when a reset has not cleared them. The repair quote form on this page sends the make, model and code to SEO Dons Ltd, which replies by email. Battery codes have their own pages: battery problems for E7, F5 and A1, and Acorn beeping for the sounds that come with them. For other makes, use the stair lift error code library.
Where this comes from
Each meaning, check and number above is taken from the documents listed here, opened on the maker's own website. Page numbers in the text are the numbers printed in each manual. How the makers' documents are checked.